prop

  1. footrope

    MaxProp Feathering Propeller - A Look Inside

    Below is a picture of my approximately 25-year-old 3-blade MaxProp, disassembled for inspection. This is the first time I have had it removed and disassembled since I bought the boat nearly 20 years ago. It has been regularly greased and visually inspected while on the shaft. The prop is going...
  2. How a Propeller Connects to an Engine

    E32-200 How a Propeller Connects to an Engine

    A beginner’s note for myself/for future reference: A quick overview of how a propeller shaft attaches to both the engine transmission and the propeller itself. Mine is currently out of the water and disassembled and so it is easy to view. The coupling bolts to the transmission and within the...
  3. T

    Discoloration of Hull @ Prop Drive Shaft

    Hey friends, I have a 1978 Ericson 27' that I put on the hard this year. After taking a look at the bottom I noticed some discoloration around the drive shaft on the exterior of the boat. I examined the inside and it' pretty dirty where the drive exits the engine and goes through the hull but...
  4. Spiny Norman

    E35-2 Folding or Feathering Prop

    Amongst the projects I have planned this fall when I haul the boat is the installation of a folding or feathering prop on the old girl. I've gone over the Yachting Monthly article about said props about a dozen times. I've also looked over forum after forum trying to get a proper grip on the...
  5. H

    E35-2 Prop Replacement Question

    Hi, all. I recently bought an Ericson 35-2 and joined this group. The zinc on the prop shaft had fallen off so replacing a corroded 13" three-bladed, fixed prop is a priority. The boat was repowered with a Yanmar 3GM30F and the shaft is 3/4". Anyone have experience with this configuration and...
  6. E

    New Prop for 1988 E 32-3

    Aloha, I have to replace my old 2 blade prop, which may or may not be the original. As of a couple of weeks ago, it has been transformed into a 1 blade prop. It is still on the boat, and I have not measured it's length, and I don't know what the pitch is. I am considering replacing with a 3...
  7. yodaears

    Surfers and antifouling a prop

    Thought i would pass this along. I had my boat hauled for annual maint about three months ago and was disheartened by the barnacle growth on the prop. I don't like the idea of painting a prop, corrosion and such. So I was asking the yard what they've heard of to help. One of the dock...
  8. juneausailin

    Prop to Strut distance E38s

    Hi all, I have seen a couple Ericson 38's, including one I just had surveyed, with a large distance between the strut and prop. The ABYC recomendation is that the distance be roughly the size of the diameter of the shaft. Does anyone know why this distance is so much greater on Ericson...
  9. P

    Prop Problems

    Have a '70 32' Ericson After having a BAD vibration when put in gear , we dove on the boat and found broken prop. Lots of corrosion and also no nut on shaft. Any help on what to expect/ shaft size/ where to find used 3 blade prop and help on problems to expect. (can it be replaced in water??)...
  10. Leander

    Ericson 35-2;Universal 3B 20-what prop?

    Ericson 35-2;Universal M3 20B-what prop? Have searched 10 years of posts, but nothing quite addresses my question. Considering buying E35-2. New Universal M3 20B with VERY funky installation: prop is 3 blade fixed 12 L 10 (12" diameter, 10" pitch, LEFT hand turn.) The correct prop should be...
  11. G

    e38 - 1981 - prop shaft stuffing box hose replacement

    Looking for some advice on replacement of the prop shaft stuffing box hose. The original stuffing box and shaft log seem to be 1 5/8". The original stuffing box hose was 4 ply. The 1 5/8" does not seem to be a common size for stuffing box replacements so a new 4 ply hose does not seem to be...
  12. R

    need E35-II prop shaft length

    Hi all, My E35-II has the companionway mounted A4 engine (3/4" shaft). I took the shaft/coupling to a local prop shop for a once over and have been told it needs replacing. Being a boat the shaft replacement price came in higher than I expected but the kicker is that they are wanting to...
  13. M

    Free wheel prop or lock it?

    I'm a new owner of a 1987 Ericson 32. I've noticed in the manual that it says to "not" sail the boat with the transmission in forward gear. My question is, does this mean the recommendation is to sail in neutral or reverse? I know that there is a lot less drag on the boat if I sail in neutral...
  14. M

    Prop Options

    I'm a new owner of an Ericson 32. I'm considering putting a new prop on the boat because I'm not impressed with the ability of the 2 blade prop to push the boat through rough water. I'm concerned about the additional prop drage of a 3-bladed prop but I don't think I'm concerned enough to plop...
  15. V

    shaft lengths and prop types

    I own an E-41, Island Bird, and recently pulled the shaft and had it inspected. Turns out I need to replace it. The two shops that inspected it both agree its beyond straightening. I decided to have a new one machined and sent the specs to Marine Hardware out of Redmond WA. It seems that the...
  16. C

    Ericson 27/ Yanmar 2gm prop size

    Hi, I'm looking to replace our exisiting 3 blade prop with a 2 blade. I think the 3 blade is too small as the boat barely powers at 4 3/4 knots. No tachometer on the boat though. Anyone have this boat and 2 cylinder diesel with a gear ratio of 2.62? Is hull speed about 5.5 knots? Thanks, David
  17. I

    Which prop for Ericson 32?

    We just purchased an Ericson 32 in California and will be moving her to BC shortly. It is our first "big" boat. New engine, Universal diesel 3 cyl (46 hours) but they left the old prop a 13x10 fixed 3 blade. Almost hopeless to try and reverse with that thing it kicks to port so badly, plus...
  18. Loren Beach

    3-Blade Feath. Prop(Sold Oct '10)

    A friend of mine is selling his Autostream (aka "Martec") feathering prop. Stainless Steel, to fit a 1" shaft. These have the external pitch adjustment, and external grease fitting. Diameter is 16". I have no financial interest -- just posting as a favor. Asking price is $1500. This may fit...
  19. D

    38 prop size

    I need to replace my current 15X11 2 blade prop and was wondering what others were using. The P.O. repowered with an M35b and am trying to make a decision on a new prop, especially for powering up the California coast. My current concern isn't so much about drag, but beating into the current...
  20. R

    Prop for E30 Plus

    I am buying a 1980 E30 Plus with the 16 hp Universal. Seller is providing a new prop at haul out but I'll have some input on the selection. It will not be a folding or feathering prop. I'd thing a two blade would be better to limit drag. Any suggestions as to what works well? Thanks, Robert
  21. D

    Proper Prop / YSB-8

    We are enjoying our '78 E-27 thoroughly, but we sometimes think she's a bit underpowered. She is equipped witha single cylinder Yanmar diesel YSB-8. Our understanding is that the YSB-8 generates about 7-8 H.P. While fine under most circumstances and EXTREMELY frugal in fuel consumption, we...
  22. C

    prop size for Ericson 32-3

    Just finished my first summer with an 1985 Ericson 32-3. Great boat. Lots of fun sailing. Different story under power where speed is slow. Getting the proper rpms under load and no load. Cruising 2400 rpm I get 4.5-5.0 kts. Engine is a Universal diesel M25. Prop is a two blade fixed 12LH10. I...
  23. Loren Beach

    Prop Comparisons, part two

    http://www.youtube.com/watch?v=B4xwJkUfU6o&feature=channel Current video of feathering and folding props tested by Yachting Monthly (UK). The rest of the article is in the magazine. I subscribe and do look forward to it each month, there being nothing to compare on this side of the pond. The...
  24. G

    Shopping For A new Prop

    Hey folks! We have had our E32-3 for nine years. We changed our :nerd:original prop from the standard fixed 2-blade to a fixed 3 blade (15x9). We are attempting to race now and we were advised that going to a fixed 2 blade (keeping it vertical) or a feathering or folding prop would increase...
  25. EGregerson

    prop shaft off set

    Hi all; there was a thread a few weeks ago re: prop shaft off set and which models have an offset and which don't; I hauled out (not just to see!) and snapped this photo. Mine ('87 E34 #243) is straight as a die. I hope this does much for the knowledge base, as i don't ordinarily like to...
  26. Loren Beach

    Prop Comparisons

    We are (Gasp!) contemplating a change to a three blade (perhaps ... fixed) prop.:cool: Everyone in the marine industry tells me that we can reduce (some or) most of our motoring vibration by changing from a two to a three. I have enjoyed the straight-line reversing and low drag under sail from...
  27. P

    removing prop shaft on E32-2..??

    Does anyone know what's involved in removing shaft in order to replace the cutlass bearing on a E32-2?......... wondering how the shaft is pulled out....could really use some good advice...thanks.
  28. P

    Prop and accoustical insulation questions

    While my E27 is out of the water (being completly repainted along with a host of other things), I pulled my prop and found it to be a 10/6. Other atomic owners I know have 12/6 or 10/7, (all 2 blade). I spoke with Don Moyer who also seemed surprized that I had a 10/6. I thought about making it a...
  29. 3

    late 80's E-34- prop shaft position

    We own a 1988 34. We have substantial wheel pull to port, mostly while motoring, but slight while glide/sailing. Boat is out of the water now, and I have noticed that the aft end of the prop shaft is about 3/4" to starboard of center/line of keel and small rudder skeg. The bronze skeg that...
  30. S

    Max Prop for sale

    I have a Max prop 14.5 in diameter for a 1 in tapered shaft. Perfect prop for Olson 34 25 hp Universal diesel. Pushes at hull speed plus and great thrust both forward and reverse as it is a feathering prop and reverses pitch in reverse so it always faces "direction you want to go."...
  31. S

    Prop Strut replacement

    My partner used my nifty underwater camera to take a nasty shot of our prop strut. What do you think? Is my only replacement option the outfit in WA? Any guess on boat yard hours for this job? Thanks, Skip
  32. S

    The proper prop?

    I have a 1990 E28 with a Universal M3-20 engine with only 835 hours on it. The engine runs great and I burn only about a quart of diesel fuel per hour. I'm getting some soot on my transom and I wonder if I'm running her to hard or is the pitch on my prop to great? My prop is a 12" fixed 2 blade...
  33. R

    MarTec Prop For sale

    MarTec Prop For sale Sold 2/01/09 MarTec RH 5 p off a Ericson 27 with a 3/4" shaft and a Atomic 4. Clean and in good shape. It is an older model, but has not seen much use. Prop Sold 2/1/09 asking 150.00 or make me an offer. Rod S. 812.3378231 rsanburn@yahoo.com
  34. Shamwari

    Need comment on prop size

    I have an e-39 with a Mistubishi 37HP and a Hurth trans ( it's not the 2:1 but the 2.?:1 one), and I have a MaxProp available for a few hours that is 14"D. I got hold of Max-Prop and they suggested a 16" at $2850 but the 14" one is only $126.50. Does anyone know if the smaller prop will be...
  35. J

    Atomic four Prop

    the bronze prop is appx 12" a (sailor)double blade,from my old Atomic 4, righthanded turn was on 3/4" shaft- is available cheap.
  36. V

    30+ prop size?

    I am going to mount a folding prop on my '84 30+. Martec asked me what the prop diameter is and I don't know. The boat is in the water and I can't find reference to the prop size in the manual. I remember it is a two blade fixed prop from the last time we painted the bottom but I didn't think...
  37. Gmilburn

    E-29 2-Blade Prop for sale

    This summer when I had the boat on the hard--I replaced the standard 2-blade prop with a new Indigo 3 blade prop. I was hoping to increase boat speed, and more importantly minimize prop-walk as I dock in and out of a tight slip. But to my disappointment, the prop walk reduction is hardly...
  38. V

    Prop Shaft & Packing size for 30+

    The gland nut on my 1984 30+ is beginning to drip very fast when the shaft is not turning so I plan to try and re-pack it this weekend. The location is very difficult to get at as is normal I suppose. I hope to buy the packing flax before going to the boat this weekend. Does anyone know the...
  39. Mikebat

    Props for the Campbell sailer prop

    Launched Valinor this morning after two coats of bottom paint at the boatyard, and a new 3-blade Campbell sailer propeller to replace the original 2-blade washing-machine-agitator. The difference was immediately noticeable as soon as I pulled away from the dock and throttled up. Gone is the...
  40. V

    Folding Prop for Ericson 30+

    We are starting to do club races with our 1984 Ericson 30+ and are going to make our first upgrade a folding prop. Does anyone have recommendations for the one that works best? Thanks, Vern Kleist:confused:
  41. J

    Need a new prop

    I have a 1980 E25+ with a volvo penta md2b (?) diesel -still have the folding prop that was on it when I bought the boat in 1983 and I think it's time for a new one. Can anyone give me any advice --or maybe just order one and install it for me? Thanks.
  42. R

    offcenter prop strut from the factory???

    a dockline tangled in the prop-diver removed it. hauled the boat for a new paint job. found the strut bent--heated it up with a torch{temporary fix for now}. 1973 35' model. why is the bronze strut offcenter? none of the other boats in the yard are like this.
  43. R

    Prop choice & Shaft thread size? (E35MkII, A4)

    Hi there, I am hoping someone can save me a 1 1/4h drive each way to my boat. I have just found out this morning that the person who was meant to have resurfaced my indigo prop and installed it prior to todays launch hasn't/can't/won't. I need to (a) get a new prop pronto and (b) a new castle...
  44. R

    Martec RH 5p Folding Prop

    I was cleaning up the shop and found a Martec non-geared folding prop in very good clean condition , forgot I had it. 3/4"-7/8" with nylon insert 5x12 etc. Used with an Atomic 4. 250.00 OBO.
  45. G

    Underwater hull cleanning and prop replacement

    I came across a scuba diving company that offers underwater hull/prop shaft cleaning. It's affordable ($5.5 per foot) and I am inclining to do it (my E29 was in the water this winter and I think the winter before since the PO did not care much about her). Is it worth doing or just waste of...
  46. G

    "Rebuild" a prop?

    The local boat yard is replacing my cutlass bearing and has told me that the folding prop has a lot of play in it. They are saying that play may have contibuted to the demise of the bearing and that I should consider having them send the prop back to the manufacturer for a rebuild to prevent a...
  47. Randy Rutledge

    Prop log tube glassed in

    I started replacing the packing for the prop shaft and intended to change the rubber tubing at this time on my 1978 E29. I started removing the clamps and realized that the rubber tubing is glassed into the prop log. Has anyone else seen this and any recommendations for the removal of the...
  48. S

    A new prop? verify your transmission ratios

    My 1987 E34 with a transmission serial no. of HWB 100-2.0R actually is 1.8:1 not 2:1 as one would think. This correction allowed me to order a properly sized prop rather than 1" too large. Always measure the engine rpms vs the shaft rpms unless you know for certain.
  49. S

    Prop Protector (shaft blade cutter)

    For sale: Prop Protector (shaft blade cutter) This is a used Prop Protector, used to cut lines wrapping around the shaft/propeller, is in excellent condition. Price is $145 plus shipping. The new price is $330. It mounts on a 1" shaft and is extremely simple and easy to maintain. With its...
  50. J

    New Prop & Prop Harmonics

    Hey All, I have an E35 MKIII Hull#211 M25-21hp Universal. Right now I get an odd howling noise at 2000 RPM and above. I am told it's a prop issue. (Prop Harmonics) Anyone familiar with this? The current prop is a 3 blade 15x11RH. Another interesting note is that the motor is rated for approx...
  51. Mark F

    E27 prop size

    Does anyone know the largest prop (diameter) that will fit on a 1976 E27 (inboard)? Thanks
  52. S

    Anybody familiar with the Slipstream folding prop?

    I am considering this prop. It is stainless and is reported to be an extremely smooth prop under power and very efficient. Also very good for racing of course. Any thoughts?
  53. G

    Prop peeper.

    All, Forgive me but I can't remember who suggested a great way to examine your prop, prop shaft and zincs from the dock by making a sight tube made of 2" PVC or ABS pipe with a piece of clear Plexiglas at one end. I made one yesterday using a 48" length of 2" ABS pipe and one 2" ABS end cap...
  54. D

    E 38-200 3 Blade Prop Size

    Hi: I just purchased a Michigan 16x12 three blade prop from Tacoma Propellers. The technician recommended that I keep the standard size so that I got more thrust out of it. Well, the prop arrived and it seems really quite large to me. I'm not worried about drag because I sail in San...
  55. J

    Atomic4/Indigo Prop

    Pulled Penguin this morning for a bottom job and yard bent the prop shaft. (Good beginning) Got me thinking about whether or not the three bladed prop from Indigo should replace the two bladed stock unit. The yard has to pull it off so what say you? Any advice appreciated John
  56. D

    E 28+ prop size?

    Our club has recently purchased a 1983 E28+ and we are concerned with the lack of speed (about 4.8kns max) at full throttle and the strong pull on the tiller at speeds over three knots. Is there a prop that will work better on this model that has an off set prop? Dave
  57. O

    replace my own prop?

    want to swap my two blade for a three, is this something i could do in the water? myself? i'm thinking (having lost a prop on my last boat) might be a good idea to have the experience. also can anyone recomend a good size for a E35II with the universal m-25
  58. S

    E36C Prop question

    Hiya gang, hmmmm how to start this one. We have a Max Prop that the prop nut backed off (cotter pin not installed?) Fortunately it came off in the divers hand and not while the shaft was spinning. Here lies our problem, we need to buy a replacement fixed prob as a back-up and to get her to the...
  59. bigtyme805

    What prop should I buy

    I have a 1985 E30+ with an M-18 auxillary and need a new prop does anyone have any recommendations on what I should go with. I know nothing when it comes to this.
  60. C

    HELP: Proper prop size need for E-27 w/Yanmar 2GM20

    I have an E-27 with a Yanmar 2GM20F with a 12-12 prop. This prop is not the right pitch/size as it bites too hard and doesn't let the engine gain the RPM it needs to run properly. Because the prop bites so hard, it makes the stern "squat" probably about 10-12 inches. Any help would be greatly...
  61. S

    Max prop setting

    Does anyone have experience with the settings on a 2 blade Max prop? While bringing the boat home from New Jersey, I experience overheating when running above 2100 rpm. With load, the engine would only reach 2200. At first, I thought it was a heat exchanger issue. My experience with diesel...
  62. Ericsean

    Prop E-38

    I just purchased an E-38 with a folding Martec Prop. This boat had been repowered with a Perkins 4-108, and hurth transmission. Could not read the ID on the tranny. Does anyone know what tranny is typically bolted on in this situation and the appropriate gear reduction and direction (RH /...
  63. L

    Ericson 35-3 Prop Specs

    Does anyone out there know the prop specs for a 35-3 with the M25 engine?
  64. Cory B

    Overpitched Prop?

    Hi all, I know that prop pitch has been discussed on the site before, but I need a quick sanity check. We have a 15" 3-blade maxprop (adjustable) on our 1984 Ericson 35. We also have the Universal 8424 engine (not the M25 which it seems everyone else has) rated at 24hp with a max RPM of...
  65. Shamwari

    E 39 prop size

    Well, my new to me E-39 is on the road from San Fransisco. We decided to upgrade from our E-27 ( which is now for sale if anyone's interested). Can someone tell me what size prop should be on a Universal 5424 in an E-39? John Gleadle Surrey BC super07@telus.net PS. A huge thanks to Guy...
  66. D

    folding prop

    has anyone installed a flex-o-fold 2 blade on a 38? if so, what was the size and pitch?
  67. H

    two bladed prop ??

    We just returned from the Florida Keys and we were passed up by everybody while motoring. Our boat is an 35 mklll 1984 with a Universal 21 hp diesel. The motor runs great and even at 2400 rpm's and a clean bottom, we still only move at 4.5 knots sog. Will changing to a three bladed prop...
  68. R

    Folding prop

    I have given some condideration to changing the [rop on my Ericson 26 fron the standard fixed one to a folding one. I'd appreciate any input as to personal experiences. Any thoughts on folding vs. feathered?
  69. N

    Max prop 2 blade for sale

    Vikings, Recently replaced my 2 Blade feathering Max Prop and now have it available. It's a 3/4" shaft set up ( used w/my Atomic 4 ). New ones seem to go for $1300 - I'd like to get $300 for this one which is in excellent condition. If anyone's interested please e mail me back at...
  70. P

    E36RH Prop Strut Movement; and excessive 'pull' to port under power

    I purchased a 1982-E36-RonHolland last October. The prop strut is loose: with sideways pressure it will move about 1/8" to starboard, then return when the pressure is released. Does anyone have a drawing of the shape of the strut and how it is installed. It appears to be glassed in, with no...
  71. E

    Spin the bucket? (Reverse for Sailing?)

    OK, a call for opinions backed by data if possible - this should be fun, as there are never any opinons offered up here.....:devil: Here's the scoop. Emerald has a 3 bladed bucket for a propeller. I couldn't care less at this point about the virtues of feathering/folding/2 versus 3 blade...
  72. E

    CDI Perfect Pitch Prop

    Does anyone have any experience with these propellers? http://www.sailcdi.com/ppmain.htm Thanks! .
  73. B

    Prop Shaft Strut Source/Replacement: Ericson 36C

    I am buying an Ericson 36C with a broken propeller shaft strut. Does anyone know where a strut is available or who can make one? Also, how is it attached? How much fiberglass needs to be dug out to get to the base?
  74. S

    E32 Prop Diam/location/clearance

    E32 Prop Diameter & Cutless-Prop Distance I recently repowered my 1978 E32 from an old Yanmar 2QM20 to a new Yanmar 3YM20. The engine purrs but I find my self between a rock and a hard place. The boat has become darn near impossible to reverse to starboard out of my slip and when under...
  75. S

    E32 Prop Nut to Rudder Distance

    Can anyone tell me the distance from the end of the prop nut to the leading edge of the rudder on an E32 (1978)? If anyone could make a quick measurement, I would appreciate it. I believe that my shaft is to far aft after an engne replacement. Kirby Ericson 32, Alamitos Bay (Long Beach)...
  76. wurzner

    KIWI Prop Customer

    I just ordered a new Kiwi 3 bladed featherer for my boat. Without wanting to start prop wars reminicent of the diesel/A4 wars, I elected not to querry the list. It cost 1300 delivered including an expedite fee to have it here in 5 days, so I'm looking forward to it with my new M35 engine. I...
  77. S

    Martec Folding 13DX12PX1" shaft prop

    MARTEC RH13DX12P, 1” Shaft folding propeller. I purchased this MARTEC for my Ericson 32 but elected to stay with my fixed pitch Michigan instead. The prop is used but in like new excellent condition. There is one extremely small ding in one blade but it will not affect performance and can be...
  78. Shadowfax

    Stock Prop on E34

    Does any one recall the stock prop on a vintage 88 E34? It was a Michigan Sailor, 1" shaft, RH, but I can't remember the size and pitch. Can anyone help me out?
  79. S

    E32 Repower, New Prop

    I have recently re-powered my 1978 E32 from the old Yanmar 2QM20 (20 HP at 2600 rpm and 2.14 gearbox) to a Yanmar 3YM20 (21 HP at 3600 rpm with a 2.21 gearbox). The new engine fits nicely in the compartment but required extensive modification of the rails and a 3” shaft extension. My old...
  80. D

    Martec Eliptic Folding Prop

    New, never used. RH 16Dx12Px1" tapered shaft. $400. daclenard@yahoo.com
  81. D

    Autostream 2 Blade Feathering Prop

    RH 16D, currently set at 14" pitch, 1" tapered shaft. Used infrequently. In water only 2 months. Virtually new. Performance was exceptional. $800. daclenard@yahoo.com.
  82. J

    Prop shaft diameter for 74 E27

    Hi Does anyone know offhand what the diameter of the shaft is for an E27...i need to change the zinc while in the water and want to have the right one on hand when i can get a diver over..i believe the shaft to be original with the original Atomic 4 inboard....for some reason iam thinking...
  83. R

    E25+ W/1GM Diesel, Prop size

    My 1983 has a 12x10RH prop. After replacing the cutless bearing, shaft and coupling half this winter season, I now discover that the prop tip clearance is 9.2% or 1.11". From what I have learned the tip clearance should be 10% - 15% of prop DIA. What size props are the rest of us E25's...
  84. M

    Prop Puller in Nothern NJ or Southern NY

    Does any one in either the Northern NJ or Southern NY area have a prop puller that they would lend/rent? I finally convinced the captain to go for the Indigo Prop (gee I really miss the excitement of backing out of the slip). Now we just need to persuade the old egg beater to relinquish it's...
  85. R

    Installing Indigo Prop

    I just received an Indigo 3 blade prop I ordered for my E27 with Atomic 4. The good comments from owners on this forum made me decide to try it. :) I noticed the instructions recommend using some valve grinding compound when installing it to get a good fit between the hole in the prop and...
  86. S

    Correct or Ideal Prop for E29 w/Atomic 4?

    I recently purchased a 1971 E29 and am in the process of bringing her back to life. Just finished installing a rebuilt Atomic 4 and now need to replace the existing prop (an old 2 blade). Are there any suggestions on how I determine ideal prop size, pitch & 2 or 3 blade? I've heard that stock...
  87. Shadowfax

    Wanted Martec Prop

    Been watching Ebay without much luck, so I thought I'd try here. I'm looking for a used Martec folding prop. Martec suggests a 15 X 14 X 1 RH. I find 16 mostly on Ebay. This is for a E34 Thanks, Paul
  88. rotorhead

    Overpitched Maxprop

    Last time we went sailing, I could not get the engine (Yanmar 3JH2E) past 1,800 rpm, so i suspect the Maxprop is overpitched. Based on the engine's user manual, maximum HP should be around 3,400-3,600 rpm. Does anybody knows if adjusting the pitch on one of these props can be done underwater...
  89. N

    PYI Flexible Coupling & Prop Overhang?

    I was just about ready to install a PYI 910001 Flexible Coupling on the M-25 in our E32-3 and started reading the posts on this site. I am just not sure about sliding the shaft back another 1.28 inches. I would still have enough room to repack the stuffing box but having the prop back furthur...
  90. J

    35' and prop performance

    I'm tied of lousy reverse performance with my stock prop. Going to haul her soon and want something that'll work. Still have my Atomic 4 which I love.
  91. mark reed

    wanted: spare prop for E38-200

    wanted: spare fixed prop for E38-200 Previous owner installed a Max-Prop but didn't pass along the original fixed prop. I'd like to carry a spare fixed prop, either 2- or 3-blade, onboard.
  92. A

    Prop size calculator

    Is anyone aware of any links with a calculator to figure the proper prop size for a given boat and engine. In my case I have an E-27 with a Yanmar YSB-8 and no tachometer. How do I calculate for the best efficiency of a given prop size, pitch, and number of blades?:confused:
  93. jmoses

    12 x 6 RH 3 Blade Prop on eBay

    Hi folks, I'm cleaning out alot of boat stuff and have listed a few items on eBay. I have a 12" x 6" Right Hand bronze prop listed on eBay. It is for a 3/4" shaft and made by Federal. It came with my 1972 E-35 with A-4 as a spare of which I have several. It was never used since...
  94. N

    Correct Prop for 1986 E32 ?

    Hello, I'm new and in process of buying a beautiful E32. When we haul it next week I want to make sure the correct prop is installed for smoothest operation under power. It has a Universal MX25XP engine. What diameter and pitch should be installed? Any help is appreciated. Thanks - Jerry...
  95. Loren Beach

    Feathering Prop on eBay

    Autostream 3-blade feathering prop on eBay today... Link: http://cgi.ebay.com/ebaymotors/15-AUTOSTREAM-SELF-FEATHERING-PROP-FOR-1-INCH-SHAFT_W0QQitemZ4591064510QQcategoryZ31281QQrdZ1QQcmdZViewItem Just shows that you never know what will show up there in the sailling hardware section... Loren...
  96. T

    3 Blade Fixed Prop FS

    1 inch shaft bore, 16 X 12 RH prop. This was on my E-38. Correct pitch for this boat should be closer to 16 X 10.5 or 11, but this prop could be repitched. I am using a 2 blade fixed prop now and am in the process of getting a feathering prop. I can ship this guy at your expense. Its in fine...
  97. D

    Ericson 30-1 prop alignment

    When I first got my Ericson last month I wrote asking about the underbody of the boat ( I haven't seen mine out of the water and I know it has rudder damage) and was given some very good information--to contact Bruce King for the line drawings. This I did and received them. My question is has...
  98. A

    Prop size and pitch

    What is the best prop size and pitch for an Ericson 27 with a Yanmar YSB-8? Thanks Mark E-27 Evening Tide Annapolis
  99. T

    Prop Options

    Where to buy a Feathering Prop Getting off topic but where would be the best (cheapest ) place to purchase a 2 blade featherer? Max prop or auto stream...
  100. F

    E-34 Universal 25XP - RH prop recommendation

    The 2 blade factory fixed prop just is not pushing my boat through strong chop and current, where it cavitates and the boat looses steerage due to no forward speed over rudder. I looked into a Maxprop 3 blade feathering and the shop recommended 15" diameter, 9'' pitch, 1'' shaft. The cost to buy...
Top