e322

  1. D

    E32-2 mast step plate

    I have a 1974 32-2. It was built without a compression pole. I guess when the deck got soft someone put in a pole to go from the mast step to the keel. It was right in the middle of the door that used to close between the V birth and the cabin. I took the cabin deck off to rebuild it and decided...
  2. ChrisS

    E32-2: double lifelines in the cockpit

    To comply with ocean racing rules I need to add a set of lifelines around the cockpit of my E-32. I plan on putting removable netting panels around the pushpit, but anything in the areas of the combings will get in the way of my ability to work the sheet winches. Does anyone have a...
  3. J

    E32-2 Traveler upgrade.

    I am looking for recommendations on updating the traveler on my 1970 e32-2. I bought the boat this April. The current traveler appears to be original equipment. I have sailed the boat about 15 times and trimming the main under load is quite a chore. The current method is to wrap the sheet...
  4. chtaylor

    E32-2 Gooseneck Toggle

    One side of the bracket that holds the tack pin on my gooseneck toggle has broken. Does anyone know who made the toggle for a 1977 E32-2 and where I can get a replacement? Thanks, Charles Taylor
  5. Loren Beach

    E-32-2 in Portland OR

    http://www.yachtworld.com/boats/1976/Ericson--2102328/Portland/OR/United-States I have no financial or personal interest, but can say that this is boat is really "turn key" and really has been well-maintained for a long time. Remembering back to that loooong year we once spent looking for a...
  6. Matey

    E32-2 Rig Tuning / Tension

    moved thread
  7. Matey

    E32-2 Steering re-build

    Well .. I just finished the re-build of my steering and thought I might put up a post for another poor sole who might have the same fate. It started with a wet cockpit sole. Not having good access to the area I pulled the cables and the quadrant to gain a better look. As we do .. while the...
  8. P

    removing prop shaft on E32-2..??

    Does anyone know what's involved in removing shaft in order to replace the cutlass bearing on a E32-2?......... wondering how the shaft is pulled out....could really use some good advice...thanks.
  9. Matey

    E32-2 Shroud Tension

    While the test sail on the (project) 32-2 I'm in contract on went pretty well, I have some concerns. Lower shroud tension .. At the dock and under sail the mast was in column. While the uppers stayed tensioned, the lowers had more slack than I expected even at 8 knots or so. The standing rigging...
  10. D

    Steering Parts for a 1972 E32-2?

    My boat was originally built with a tiller instead of a wheel and I'm trying to convert to a wheel. I need parts. I already have a pedestal, a wheel, and a quadrant, but the pedestal is bare. I need bearings, steering shaft, chain, and cable. Anyone have parts or know where I can get them...
  11. D

    Wanted. Steering Quadrant for E32-2

    I'm converting my tiller to a wheel and am looking for a steering quadrant that will work with a 1972 E-32-2. Also looking for any other steering hardware you might want to part with, but the quadrant is the main thing for now. Please email me at Rick@ARmoz.com Thanks, Rick Andrews The...
  12. J

    Re-sealing E32-2 Portlights

    I hope you all will bear with me... There are many threads on this site on this subject, and I've been involved with them. Also, most of the info gleaned from those threads have been immensely helpful. If this info is way old news, my apologies, and disregard! I was describing the...
  13. S

    E32-2 Stanchions

    Guys, I want to add a second lifeline to the original stanchions on an 1974 E32-2. The stanchions are single pieces, welded to the base. Removing and replacing (and rebedding) the stanchions is beyond our time/cost window for this repair. I'm considering adding a clamp on eye (see picture) to...
  14. S

    Buying (maybe) an E32-2 with a wobbly rudder

    Buying (maybe) an E32-2 with a wobbly rudder (And the ensuing tale of repair) Hello world.... First post. Not yet an owner, but have contract on a 1974 E32-2 in San Fran bay. Boat is in overall good shape, but I've found significant slop in the rudder. Survey will be scheduled within 2 weeks...
  15. chtaylor

    E32-2 Pedestal Guard

    Would someone be so kind as to give me the measurements for the extra-wide pedestal guard that is mounted on the cockpit divider of the E32-2? I want to see about having one made. As I understand, they are impossible to find. Thanks, Charles
  16. D

    Need Steering Parts for 1972 E32-2 (wheel & quadrant)

    I have one of the early Ericson 32s that had a tiller instead of a wheel. I want to convert it to a wheel but am having trouble finding the parts. I have the pedestal, but still need a wheel and a quadrant. If you either of those parts and are willing to part with it, please let me know how...
  17. C

    Wanted: Genoa for E32-2

    Hi: Looking for a used genoa in reasonably good condition for a 1975 E32-2. Ideally, it would be about a 140% with a luff of about 36ft. I'm kind of new to the Ericson community as last season was my first with this boat and would appreciate any help or advice any of you guys might have...
  18. ChrisS

    E-32-2 Spinnaker Specs/measurements

    Hello All-- After completing my first season with my "new" boat, I have had a great time and learned a lot. I'm now in the process of putting together a list of repairs/improvements to work on during the off season here in the SF Bay. I'm also going to take a trip up the Delta next June, so...
  19. S

    E32-2 extra ballast??

    Hi All I was doing a clean up under the v berth today, and while standing on my head discovered a about a dozen lead ingots that are tucked in under the aft end of the water tank.Iwas able to remove 4 of them but the rest appear to be gooped in place. They weigh 22 lb. each. I was assuming a...
  20. ChrisS

    E-32-2 Tracking and rudder size

    Hello All-- I am in contract on a 1975 Ericson 32 in really nice condition. I sea trialed it last weekend, and I really like the boat. This would be a family boat/low key racer for the SF Bay. I reading some posts on this design, some owners report that downwind steering in bigger winds...
  21. wurzner

    E32-2 Pentex 153% by Ullman

    I have an Ericson 32 153% #1 Genoa. The sail dimensions are 48 (I) and 23 (j). Thsi sail is really nice with only about 10 races on it. It has been stored off the boat and is in like new condition. Replacement cost is about $2400. Let me know if you are interested, I may sell it with the the...
  22. wurzner

    E32-2 Pentex Main by Ullman-Excellent Condition

    I have an Ericson 32 main with two full battens and 3 partial battens and two reef points. The sail dimensions are 32.75 (P) and E dimension of 13. It is a full roach sail in excellent shape with only about 10 races on it. It has been stored off the boat and is in like new condition...
  23. J

    Packing - E32-2 rudder post packing

    I have been following threads on this subject for a while, as the packing/connection at the top of my E-32-2 (1971) was leaking last season, and I want to stop the leak! The snow has finally cleared, and so I started to tackle the problem. Regarding the steering system and attachments to the...
  24. Cary Diehl

    FS: E32-2 170% Genoa

    This is a dacron, 4 oz most likely, 170% genoa for an E-32 standard rig. The sail is older, but still VERY useable. Great for those light air days that there is just no breeze. Sail has hanks, all my sails are now #6 luff tape. Asking $350.00, e-mail me if interested.
  25. R

    Powering an E32-2

    I've recently seen a mid-1980's Universal 21hp M25 engine for sale. I understand they were designed to replace the Atomic 4, and I was wondering if anyone has done so with a 1970's 32 ft or larger Ericson. Mainly I'd like to know if it has enough power compared to the A4. Thanks, Becky
  26. J

    Dodger For E32-2

    I got a quote for a dodger for my E32 that was quite pricey! Several shops offer a more attractive price if they have patterns for a particular boat. Does anyone (maybe west coast??) know of a canvas shop that has patterns for the E 32? A similar question: Has anyone purchased an...
  27. R

    1974 E32-2 stern pulpit

    My stern pulpit rail has cracked in half at the top of a stanchion. can it be fixed or do I need a new one? What costs are involved if I get a new one. Thanks.
  28. J

    mooring pendant - E32-2

    I will be mooring her in the Spring in a bay here in Long Island, the WM catalog and others sell 15' pendants and say to use a pair. Previously, I made the mooring pendants, and would like to do that again, I figured a 3/4" dia line and wonder if 15' is too long/short?
  29. J

    E32-2 cockpit Sole

    I'm concerned about the cockpit sole, seems a little soft on the forward end. Does anyone know off-hand, if it's solid glass or sandwich balsa?
  30. J

    E32-2 chainplate/bulkhead fix

    I have just purchased a 1971 E32 (Hull #199) and intend to offer a little TLC, and hopefully keep this boat afloat for many more years. I do have to reinforce/repair rotted (not totally) bulkhead/ chainplate areas, and have seen some of the discussion at this site and a couple of others. Any...
  31. R

    wanted: jib for E32-2

    Need a good quality used jib to replace mine (I think it's original from '73!). Either a 100%,110% or a 135%. Approx. dimensions are luff: 35-37'6" leech: 32-36' foot: 14-17'. Please email me at rschaffn@usc.edu, thanks!
Top