lines

I guess prior to drilling holes would have been a better time to ask .. but any input on my lines-aft layout ? On this side I'm bringing back the main halyard, 1st reef and either a 2nd reef or spinnaker halyard (depending on need). One block is backordered (halyard thru the mast plate) and I...

I plan to run the reefing lines internal of the boom on my E29 T. I plan to add two sheaves on the outside of the boom end in line with the outhaul and make guards for the sheaves to keep the lines on the sheaves. At the mast end I plan to have one exit hole with a cam cleat on an angled base...

It's time to replace my lifelines. I'll be using 3/16 SS coated, and I plan to have JSI in St. Petersburg do them. I'll send my old lines in and reuse what hardware we can safely. Has anyone had any experience with JSI, hopefully they are a good rigger. Thanks for any feedback, or better...

Had e halyards made and they slip thru my gloves, how do I age them?

Hi all, Any suggestions as to how to keep my lines from developing the green grunge from mildew? Would a dilute solution of bleach affect their strength? I took my mainsheet home and threw it in the clothes washer and it cleaned up pretty well--but after just a couple of months the green is...

My E32-3 has an array of control lines on the cabin top, including halyards mainsheet reefing lines vang control ect and they come in at wierd angles with an array of winches none of which can be cranked full circle because of their positions as compared to the dodger. I would love to see...

Can anyone suggest what diameter line to use for spinnaker sheets on an E28+. I just purchased the boat with a new, unused spinnaker but no gear. Any suggestions on appropriate line size for sheets/guys etc. would be appreciated. Thanks. Steve

I am planning to replace my cockpit drain lines this spring. What drain line material is recommended? Also, the current routing goes from the two cockpit drains to a thru-hull shared by the sink drain line. The cockpit drain lines appear to have a low point below the thru-hull; thus, water...

Can anyone sugest a place to look for a simple drawing showing thw lines of the Ericson 41 hull? Thanks, John

I'm planning my next project - leading the halyards, boom vang and reefing lines aft to the cockpit on my 1977 E-32. Is there any reason why I cannot, or should not, remove the winches from the mast and place them on the cabin top to be used for the aft-led lines? If I do remove them, will...

Good day every one we finely got some sunshine in kansas today. I started sanding on the sliding hatch on my 1977 erickson 27 the black lines between the teak boards started breaking and falling out . What are they and how do I replace them Thanks:egrin:

I am still considering a E27 here in the Chesapeak Bay area. The owner has recently had a new holding tank installed. My problem is the look of the resulting installation. The lines now feed to a pump out fitting on starboard deck (I presume because we can't dump the stuff overboard anymore). My...

On the stbd. side of the cabin top the main halyard is led in between the traveler pylon and the sea hood. There is very little room here for more lines. Currently the main halyard is led around a winch (non-st) that is forward, almost too close to the dodger, and then cleated off to a...

I have upgraded to spectra lifelines and have the old ones for sale. They are a complete set in decent condition. Make an offer. I also have the aft gate stantions as well... I removed them to make an easier access. Cheers, Geoff Nelson gnelson@netsgrp.com E-381 Pau Hana San...

Hi all, newbie owner of E27, love it! I am thinking of runing my main halyard aft so I can raise the main with less stress from the cockpit and then maybe add a reef and my gennaker halyard. Any suggestions on the best way to do this on a E27? Thanks in advance for any info. Ragamuffin E27...

I'm the new owner of a 1976 E-27. Replacing the life lines is on the project list. I've read the threads on the this site with interest. There are a couple of issues that seem odd to me. One is the way the life lines are routed inboard of the forward shroud, outboard of the middle shroud...

As a new owner of Windfall, 1984 35-3 I realize how spoiled we have been with our 30 Catalina in which did have Jack Lines. Already getting tired of doing the chicken dance on the deck trying to get the Main flaked, tied and all the wrestling involved. Wondering if anyone can guide me in the...

In my project to re-plumb my head I want to remove and clean the holding tank. I know fun job huh? In order to remove the tank I need to remove a small shelf in my cockpit locker that the compressor for the fridge sits on. Looks to me like they have special fittings that can be disconnected on...

Hi, I just purchased a new (old) Ericson 34. I am thinking of installing Jack lines, as they make me feel secure when properly used. Where on the bow is a good place to put an attachment? Any ideas on what to use? Thanks

Can anyone recommend good locations for hard points for jack lines on the E35? As I rebuild my deck, I would like to put stronger coring at those locations. Gareth Freyja E35 #241 1972

I am looking for a set of drawings or lines for the E23 Mk 2. I would like to do a solid model in some CAD software with them. I am also an RC sailor and might like to do a scale model of my full size boat. I could also work from a table of offsets. Anything would be a help. Any ideas...

What have you guys done about sealing the barbed ends of sanitation lines? I know that I can use some dish soap to lubricate them to mount the house - or heat them some with hot water - but what about actually sealing them? Has anyone actually used a type of sealant to prevent leaks at the...