Recent content by Justin Lee

Gravitystorm is SOLD I sold Gravitystorm to a very nice local couple. It has been a pleasure being part of the Ericson family. Thanks to everyone for the help & support found on this forum.

The time has come for me to sell "Gravitystorm", she is a 1985 Ericson 32-III. I am the third owner of this boat. I have kept her on a freshwater lake in Northern Utah for the last 10 years. I have "gone-through" every facet of this boat & upgraded or replaced almost EVERYTHING! This boat...

I went for the Slim Square one...model #IT-SS-16-110. It takes up MUCH less room than the old round one & was a cinch to mount/install. It only holds 4.2 gal but that is more than I ever need. This unit was also easier to get into the hatch & work on than that old round job! I highly recommend...

Isotemp I did the Isotemp thing myself...very happy with the result! I will say that I had to cut the hatch opening wider to get the old unit out...bring a sawzall! :egrin:

380? ...I didn't know there was such a thing as at "380"...but I guess there is! This looks like something that a person could do to a late model 32-III? Has anyone looked into this?

I saw the attached picture somewhere on this site. It is apparently an unfortunate incident involving a 38, but what REALLY has me intrigued is the "Swim Platform"! I am curious as to who's boat this is...and how was this modification done? If you know anything about this...please enlighten...

Per Kim's request from the thread "Hello out there" I am going to post a little information about Bear Lake in Utah/Idaho. Bear Lake is a fresh water lake straddling the Utah/Idaho border. It is about 20 Miles long (North-South) & about 8 Miles wide. There is only one marina on the lake...it is...

Patterns you say!?! ...well Goeff, I have been trying to make patterns but it has not been easy. My boat is about 2.5hrs away. Up until a couple of weeks ago there was 2ft of snow on the docks so it was very treacherous & COLD to venture up there! Weather has finally warmed up enough to get...

Lake Racing? ...glad to see some stuff going on in this forum! We're just south of you on the Utah/Idaho border at Bear Lake. We have had some difficult years with water lately...but things have been improving the last couple of years :egrin: I agree with asking for extra points for...

Router vs Rotozip? Geoff, not sure if you are still watching this thread or not but wanted to ask a few questions. I am beginning this project & am quite concerned about cutting the plywood. I noticed that you appeared to use a "Laminate Trimmer" rather than a full blown Router. Was this the...

I am leaving my 32-3 in the water over the winter this year for the first time. This is a fresh-water lake in Northern Utah & it normally freezes completely over by about mid-January. We have about 12 boats staying in this winter & have installed several "Bubblers" to keep the area where the...

I am considering adding a dodger to my 1985 E32-3, I live in Utah & there are no canvas shops here that I trust to do this correctly. I will probably look at a shop on the West Coast & was wondering if anyone has had one made for this particular boat...are you happy with it & would you recommend...

You've got soul! Geoff, it has been awhile since I have been on the forum...we were unable to even use our boats last year due to low water. I am hoping for a VERY wet spring & perhaps at least a month or two in the water this year! I am fascinated by your cabin sole project as I have been...

I am looking to add some type of backstay adjuster to my 1985 Ericson 32 this year. I thought I might ask if anyone has one they want to get rid of before I buy a new one? I'll consider any kind but would prefer hydraulic.

...Yes, It ONLY happens in Reverse? I can run it at almost full throttle in the slip tied up in forward & NO black soot??? I too can reach hull speed at about 2200 rpm's with my Maxprop, I may try to reduce the pitch this winter. Unfortunately, I have to pull the boat out of the water this...