hoses

  1. J

    Scupper Drain Hoses

    On a E-35 Mk III does anyone have an idea why two of the scupper drain hoses go to a "T" and then go to a below the water line through hull to drain? Doesn't seem to make sense that they would drain below the water line. This is in the context of winter storage in the water. Thanks, John...
  2. D

    Hoses And logo

    During bottom painting project of our '78 E-27, we replaced all thru hulls and seacocks.($$!) Now it's time to replumb head and several other hoses. we are also planning to add a soft water tank up under the v berth to existing hard water tank (15 gal). Rinsing holding and water tanks. I did'nt...
  3. F

    Replacing blower motor/vent hoses: Ericson 30+

    The blower/vent hoses at the stern of my ericson 30+ are getting old and torn in a couple of places (looks like 4" plastic/vinyl dryer vent material!). While I can get at the port side easily through the cockpit locker, the starboard side has no cockpit locker, and while I can see the hose...
  4. S

    Head Hoses Replacement

    It's time to replace the Head hoses on my 1988 32-200. I plan on using Trident #101 Sani Shield. Has anyone done this on a 32-200 and know how much hose you used? I was thinking of buying a 50 foot roll until I saw a price for the hose.
  5. rotorhead

    How to pass Hoses, cables thru the innards of my Ericson

    I just discovered that my bilge pump is not working, so I installed a backup while the repair kit of the old one arrives. I think of leraving the temporary pump as a backup, but passing an additional hose thru the innards of the boat seems challenging. Any suggestions who to do this...
  6. T

    Insulating Coolant/Exhaust hoses

    My cockpit locker gets pretty hot in the summer from the exhaust hose and hot water heater hoses as well as the expansion tank. I was thinking of insulating the hoses to keep the heat down as this heat tends to make its way over to the aft cabin too. Also the fridge compressor is in this locker...
  7. Lawdog

    Replacing head and hoses

    I will be replacing my Lavac toilet on my 1983 E38 with a manual model, and was hoping someone has pics of an 80 to 85 E38 head and hoses so I can see what they are supposed to look like. My prior owner installed a Lavac which I dont particularly like, and will probably give away, and has hoses...
  8. R

    M-25 fuel hoses

    Hi dear all, does anyone know the diameter of the fuel line between an electric lift pump and the secondary fuel filter for the Universal M-25? One document I found says 5/16, other says 1/8... Thanks in advance, Stanly
  9. Luffin it

    Re doing the hoses and head

    My question is why would the out going line on the holding tank be reduced to 1.25 and then tee and go back up to 1.5? Incoming is 1.5 from the head. Was it a clearance problem which could be fixed by building up the surface the tank sits on? Fisheries Supply had no Idea but thought it should...
  10. T

    hoses

    I am planning to replace the 5/8" bildge pump hoses and the 1-1/4" scupper hoses on my E35. What type of hoses should I use?
  11. Sean Engle

    Heater Hoses - M25

    I have a Universal M25 diesel in my 35-3. I just installed a new Iso-Therm water heater, and it's inlet/outlets for the heatexchanger are 1/2" instead of the 7/8" that was on my Raritan. Can I just replace the hoses and fittings, and reduce them to 1/2" - or will I be harming the engine and it's...
Top