bracket

Try as I may, I cannot find any information on the source of the ladder bracket pictured. There are two of them on my boat, 13.5" apart. The ladder itself is missing, and I'd like find the corresponding ladder-side doodads that clip into these brackets. Thanks!

I just sold my E-27 in anticipation of purchasing an E-30 Plus. The bad news is while inspecting the 27 with the new owner we discovered the spreader bracket had cracked. I've been doing the google search for some time to find a replacement and haven't had success. Any idea's? update...

Getting ready to step the mast today and what the hell, broken spreader bracket (not sure if that is the official name but the bracket that bolts to the mast that the spreaders attach to). I think it was likely broken through mishandeling during the mast take down last fall rather than fatigue...

What is it? I've seen it mentioned in several places. Is it something I should do on my M-18? I understand that the stock belt will not fit with this mod.

Hi all, I'm searching for a source for the mate to the bracket mounted on the rear of my E29. I have searched the web and contacted a couple of outboard bracket builders--and while they are willing to custom build one, it would be expensive. Does anyone recognize this bracket and may be able...

Last week I took my alternator in to the alternator shop as it was only putting out about 12.1 volts. It needed a new regulator. It was serviced and some kind of waterproofing put inside. 80 bucks. I was unable to tighted down the alternator bracket tensioning bolt. I discovered that it...

All, I just stumbled on this bracket on eBay for anyone thinking of getting one. It ain't mine, I don't know who's selling it and I'll be just as poor after it sells. Glyn Judson, E31 hull #55, Marina del Rey, CA

I need to replace a broken Spreader bracket on my 1977 E25. Does anyone have one, or know who makes replacements. Pic is of good one! thanks

Murphy got me today. I dropped the stick with a couple of buddies. I broke the bracket that was bolted onto the mast on my E25. What I need to know is there a source to buy this part? Is it made of aluminum? I know I can have one made, but I was hoping that I didnt need to go through...

Hi Guys I am installing the alternator bracket upgrade on my 82 M25 Universal. I searched the previous posts and see others have completed the upgrade in a short amount of time. I have the old bracket off but cant get the studs out of the coolant case attached to the engine block. Any...

Aloha, I am looking for 10-15' of mounting bracket for the rub railing on my Ericson 27. Anyone know where I can get some? I bought the Ericson 27 on this page for $4000, yea baby! Thanks, Big Kahuna

The PO had the outboard installed on the bracket shown in the attached image, even though the transom has the cutout. Could anybody give me some possible reasons this was done? Thanks, Joe Williams

I have an original cast aluminum port side spreader bracket in excellent condition for sale best offer. I do believe that these were used on e-25's and e-27's as well. :egrin:

I am looking for an E-23 spreader mounting bracket between spreader and mast. I need the port side bracket if anyone knows where I can find one, it would be great. It is a Sparcraft airfoil type setup and mine is broken. :confused:

When i inspected my shifter cable on my 70Ericson29 i noticed that a metal bracket holding the end of the cable in place and mounted to the bulkhead separating the battery compartment from the engine was badly corroded and literally falling apart. I put it on the repair list for the mechanic...

HI, everyone. I am in need of a spreader base bracket, (Port side) broke mine a couple days ago while climbing to install a windex. So far i have had no luck in finding this piece anywhere, places i have called are pacific seacfraft, RigRight, LeFiell manufacturing. Any help or sugestions...

HI, everyone. I am in need of a spreader base bracket, (Port side) broke mine a couple days ago while climbing to install a windex. So far i have had no luck in finding this piece anywhere, places i have called are pacific seacfraft, RigRight, LeFiell manufacturing. Any help or sugestions...

I have removed mahogany cover and found that the original chainplate bulkhead had been reinforced by a previous owner. It looks like they also added (2) more stainless brackets for more support. One bracket is in the head on the other side of the bulkhead, and the other partly overlaps the...

Garelick 71056 stainless steel outboard bracket (for long shaft outboards) and Thetford Aquamate 885 electric (battery) flush tall profile porta potty head (BoatUS item no. 198123). Both brand new, never installed or used before Isabel took care of my boat. Reasonable offers, you pay shipping...

I OWN A 1975 ERICSON 23' SAILBOAT. I AM HAVING DIFFICULTY LOCATING THE TEAR-DROP SHAPED MOUNTING BRACKETS FOR THE SPREADERS. DO YOU HAVE ANY SUGGESTIONS ON WHERE I MIGHT FIND THESE?

I have seen mounting brackets at the mast base for the purpose of attaching blocks to run halyards and control lines aft. My '76 E35-2 mast is deck stepped and I'm not certain how a bracket would be mounted or where to find one. Any 35-2 owners out there who have done so?