View RSS Feed

Recent Blogs Posts

  1. She's got sole!

    Floor frames were carefully measured and cut to float a cm off of the hull, glassed on both sides and epoxy sealed edges, then tabbed into place with 3 layers of 17 oz tabbing. A large 3/8" G-10 backing plate, big enough for the two cooling-water thruhulls & valves, was also glassed in at this time as the tabbing for the floors overlapped with it. This location will be under the galley extension/sink area, which should provide quick and easy access through a cabinet door. I never understood ...

    Updated 12-13-2019 at 08:19 AM by texlan

    Categories
    Uncategorized
  2. An uplifting change!

    I went ahead and glassed in the old engine controls panel hole and shifter/throttle hole, as they were located in prime leak water into the boat locations. There was also another hatch near the gas fill in the starboard aft cockpit seating that got glassed in, as well as the gas-fill hole itself. This was done with a couple of pre-cured layers of 1708 as a backing plate and then 4-5 layers of 17 oz biax on the outside, with Total Boat Total Fair as the fairing compound. Some images of the process... ...
    Categories
    Uncategorized
  3. Working through it

    This girl needed a real new lease on life. It needed a new backbone..err mast compression post step. It needed a new sole. We could rebuild her... we do have the technology. She could be more than just 'no problem.' She could be spectacular.

    I'm a big fan of electric motors, and with a high capacity 48v propulsion bank we could go to electric cooking...remove the explosives from the boat. My risk-adverse nature likes that.

    I had a plan. It was a systems oriented plan, ...

    Updated 12-11-2019 at 07:02 AM by texlan

    Categories
    Uncategorized
  4. New beginnings

    Even though I'd stepped back, I did manage to, over a year or so, finish out the new sump and engine bay pretty nicely, and even got the nuisance pump (A whale 320 gulper with air pressure switch) installed. I keep a 5 AH RC lithium pack on it for now, to handle the occasional small leak when it rains, though the # of leaks keep getting smaller lately.. it's very encouraging.
    Click image for larger version. 

Name:	sump-2.jpg 
Views:	6 
Size:	91.7 KB 
ID:	28157Click image for larger version. 

Name:	sump-3.jpg 
Views:	9 
Size:	138.2 KB 
ID:	28158

    I fashioned new laminated engine stringers, ...

    Updated 12-10-2019 at 10:56 PM by texlan

    Categories
    Uncategorized
  5. More Debuilding and some scope..

    I was starting to feel pretty good about the sump situation,

    Click image for larger version. 

Name:	newsump2.jpg 
Views:	11 
Size:	130.3 KB 
ID:	28153Click image for larger version. 

Name:	newsump1.jpg 
Views:	10 
Size:	121.3 KB 
ID:	28152

    but once you start cutting, it becomes an addiction. There was the Great Rotten Galley Removal of '17..
    Click image for larger version. 

Name:	teardown.jpg 
Views:	8 
Size:	157.8 KB 
ID:	28154

    The delaminated cabin sole liner..
    1/3rd way through cleaning here.. (PS when using mineral spirits, wear a vapor respirator. I got sick for 3 days after a half hour of this..)
    Click image for larger version. 

Name:	sole.jpg 
Views:	9 
Size:	127.5 KB 
ID:	28155 ...
    Categories
    Uncategorized
Page 1 of 99 123451151 ... LastLast