• Untitled Document

    Join us on March 29rd, 7pm EST

    for the CBEC Virtual Meeting

    All EYO members and followers are welcome to join the fun and get to know the guest speaker!

    See the link below for login credentials and join us!

    March Meeting Info

    (dismiss this notice by hitting 'X', upper right)

bearing

  1. B

    Wheel feels sticky while underway

    While I'm underway in my E29 it feels like my rudder is sticky. At the dock it feels free and easy but after a particularly big run in front of a twenty knot blow and accompanying seas all of the sudden it feels like something is wrong. Everything looks fine at the top of the rudder post where...
  2. H

    cutlass bearing

    I need to replace the cutlass bearing, is this a job for the ship yard or is it a project I can do during a haul out and bottom job ? 1984 mkII 4'11" draft with a Universal xp25 diesel engine? Thanks, Chip ( Hat Hanger )
  3. ignacio

    E35-2 Rudder Bearing Replacement

    Hi all, I'm going through the surveyor's findings and recommendations on a 35-2 I'm considering purchase of, and the survey include the replacement of upper and lower rudder beariings. After speaking with a yard about this, it's clear more information is needed. So, how does one go about...
  4. S

    E-27 Cutlass bearing

    I’m a new E-27 owner, and it appears I have a Cutlass bearing issue. The bearing has separated from the strut, and will need to be fixed. I assumed I just need to attach to the brass (?) casing to the strut and all would be good; however, all the pictures that I have seen – it appears there...
  5. R

    cutlass bearing

    Yes its time to change the cutlass bearing on mat E35-mark2.Anyone know what I can expect to pay? Is the shaft on a strut. any advice would be appreciated, ' Ralph Ericson owner-"another fine mess'
  6. D

    E-27 cutlass bearing

    We have a groaning sound on Desiderata when we put her in gear. Both forward and reverse. I feared for transmission problems, but a friend (NOT a boat expert, but good mechanic) listened to it and suggested the noise wasn't "metallic" enough to be the transmission and may be the cutlass...
  7. D

    Ericson32-3 cutlass bearing.

    I recently had to replace the cutlass bearing in my Ericson32-3 and our Yard Manager came up with an ingenious way to install. Rather then drop the rudder for shaft removal, he removed a few hoses and lifted the engine high enough to slide the shaft under the engine and out of the strut. Pressed...
  8. D

    Cutless Bearing

    I have a 1989 Ericson32-3 and I have to replace the cutless bearing. I know the bearing is 4 inches long and the shaft is 1 inch. Does anyone out there know the outside diameter of the bearing. I need to get one ordered so any help is much appreciated. Dan Callen Ericson 32-3 Andiamo
  9. T

    St4000+ Raymarine Wheel pilot problem installing bearing cage

    We hit heavy sea's a month ago, somehow the wheel pilot got engaged and the wheel was turned resulting in the drive ring cracking and breaking, ball bearings popped out everywhere. I have gone through the owners handbook and can't figure out how to get the bearings into their cage and then into...
  10. Dferr

    E-38 Cutlass bearing

    Happy New Year all! I tried to do a search on this, but didn't find it. Anyway, does anyone know the correct size Cutlass bearing I need for my 1982 E-38? I measured 5 1/2" long x 1 1/4 OD, does that sound correct? Also, I don't find any set screws in the strut, is that correct? Should I go...
  11. S

    Advice HH Bearing Compass

    I am going to purchase a handheld bearing compass. Anyone have a good suggestion for me? Either what to look for, or a favorite brand. Price isn't as important as utility, durability, and usability.
  12. J

    E29 Cutlass Bearing

    I need to replace the cutlass bearing on my E29, and cannot determine whether it is just the rubber bearing that needs to be pulled, or the bronze sleeve surrounding the rubber bearing as well. If it were the bronze sleeve, i would expect a set screw in the strut which would hold the bearing in...
  13. M

    1975 e27 strut bearing question

    Mechanic working on my a4 says the bearing is worn. In his words it's shot. I know he's very overly cautious, and I appreciate that. BUT, I really want to FINALLY get her wet and begin sailing! (she's on jacks currently) He insures me that if I don't fix it (as I'm inclined to wait until...
  14. footrope

    E38 Rudder bearing (bushing?) maintenance

    I've been reading some good threads on the rudder bearing and bushing maintenance that some of you have done. It helped me a lot when I dropped the rudder yesterday in the yard to clear the way for the prop shaft to be removed. We dropped it before putting the stands in place, and only had to...
  15. D

    E380 Cutless Bearing Replacement

    Hi Everyone - long time viewer, first time poster. I'm in the middle of a cutless bearing project and wanted to bounce a few questions off the forum: 1) Set Screws: There are no set screws on the existing strut and bearing - appears to have been a pure "press fit". Folks at the boatyard are...
  16. D

    cutless bearing change on E-32

    how hard is it and what does it cost?
  17. ChrisS

    worn cutlass bearing

    I just had the bottom cleaned, and the diver noticed that the cutlass bearning is getting pretty worn (the surveyor said it was 30% worn one year ago), and indeed, there seems to be more vibration when motoring. Aside from the vibration, is there any danger in putting this job off? Will it...
  18. B

    Ericson 36C Cutless Bearing

    We are replacing the propeller strut on an Ericson 36C, which also means a new cutless bearing. The bearing we purchased has a clearance of several thousands of an inch (haven't actually measured it) to the propeller shaft. Shouldn't there be zero clearance? Shouldn't it be an interference...
  19. R

    Rudder Bearing Questions (E36-RH)

    Sorry I borrowed a picture until I can get out to the boat and take some... Is the bronze piece in the picture with the arrow pointing at it supposed to rotate with the shaft or is it supposed to stay stationary with the fiberglass tube? I've been finishing up a re-power and I noticed last night...
  20. treilley

    E35-3 Cutlass bearing

    Can anyone give me the make, model and source for this bearing? Thanks
  21. S

    cuttlass bearing and strut repaired 36c cont

    We rigged up a line thst went oner the stbd cap rail from the port sheet winch to the strut .Then we set up the hooka rig. I went over the side with a 4lb hammer and as my wife kept the line tight I spent the next 2hrs hitting the strut thats a tuff job underwater. We were able to get about half...
  22. S

    cutless bearing and strut repaired 36c

    What ever you do, do not run over the floats of a fishtrap in Pureto Rico in the middle of the night. We did. At about 2300hrs we on our way off shore from the s/e end of Pureto rico headed for Sun Bay in Visquez (Spanish Virgins) motorsailing into 12kt winds 4-5 swell all on thr nose (noserly)...
  23. S

    Cutlass bearing 36c and strut

    I'm in the yard in Venezuela. We hit a fish trap in PR bent the strut real bad but the shaft shark cut it off. I was able to some what bend it back but not far enough after 2hrs of underwater hammering with a 4lb hammer and a hooka rig. It got us this far.Got the shaft out, it's bent and...
  24. E

    Rudder Bearing Replacement

    I need to replace the upper rudder bearing on my 90' Olson 911 SE. Does anyone have any experience with this ? I would also would prefer to go with a roller bearing to replace the stock friction. Any recommendations would be appreciated. Ed.
  25. Bolo

    Cutlass bearing replacement

    Thinking ahead somewhat, I need to replace my cutlass bearing on our E-32 (1987) which we just bought a few months ago. I'll be doing this sometimes after haul out near Thanksgiving, along with putting in a dripless stuffing box and maybe even a folding or feathering prop. But the most...
  26. E

    Cutless Bearing E 38

    Does anybody know the cutless bearing size for an e 38 and is there anything I should know when replacing it. I am going to pull the boat next week for a coat of paint and would like to have a cutless bearing on hand as I don't know if it has ever been replaced.
  27. C

    Cutless bearing removal

    Can the cutless bearing on an E-27 be removed without disconnecting the propellor drive shaft??? Thanks chris
  28. Y

    Cutlass bearing on E32 1970

    Hello, I bought a E 32 1970 and I would like to change the cutlass bearing because there is some vibration. I cleaned the strut and found out that there are no set screws !!! It looks like there is no brass around that bearing (only rubber). Did anyone ever change a cutlass bearing on an...
  29. J

    Cutless Bearing

    Has anyone found a good source for a cutless bearing? I have only found West Marine. They do not stock the one that fits the E27. Thanks for your help.
  30. C

    E38 Strut Bearing Replacement

    Thanks to all who replied to my request for info on removing the strut bearing from my E38 strut bearing. The yard tried to do it with the special tool (mentioned by some who replied to my original posting) and with the shaft still in the strut bearing. It didn't work because the bearing was...
  31. C

    E38 strut bearing

    Does anyone have experience in replacing the strut bearing on an E38, vintage '84? Is there a set screw? Do you need to remove the prop shaft? Peter
  32. C

    lStrut bearing, etc.

    I am about to haul out my 1984 E38 and am seeking the following information prior to haul out: 1. Does the strut bearing have a set scew? If yes, where is it? How do you get the bearing out? The prop shaft seems to be pretty well corroded into the coupling. 2. How advisable is it to replace...
  33. J

    Cutlass Bearing on an E-28

    I am in the process of purchasing an E-28 1987 and the engineer strongly advised that the Cutlass Bearing be replaced to avoid secondary damage. Unfortunately, where I live in Huntington, NY none of the local boat yards have the proper 3/4" tool to pull the bearing out, so it may necessitate...
  34. Graham Cole

    Rudder bearing 30+

    I have slop in the bronze bushing/bearing (lower). It looks like a bear to replace this bushing. I tried wrapping the rudder post with mylar film but now want a permanent solution.. Does anyone know how to fix without changing the bearing... Ideas? thanx
Top