• Untitled Document

    Join us on March 29rd, 7pm EST

    for the CBEC Virtual Meeting

    All EYO members and followers are welcome to join the fun and get to know the guest speaker!

    See the link below for login credentials and join us!

    March Meeting Info

    (dismiss this notice by hitting 'X', upper right)

rebedding

  1. Can I use a lifeline?

    E26-2 Can I use a lifeline?

    My attempts at getting away with a project for labor-only were once again thwarted. I took the lifelines off last fall with the intent of taking them home and scraping off all the old plastic coating. The turnbuckles initially wouldn't unthread, so I took the whole tangled mess of wires and...
  2. F

    Help please from Butyl Tape experts on rebedding

    hi, I have read the various posts on rebedding deck fittings with butyl tape. I very carefully rebedded several stanchions with butyl tape--cleaned the area thoroughly, placed a 1/16" base of butyl on the deck under the stanchion base, wrapped each of the bolts in butyl tape "worms", etc. A...
  3. wolly bugger

    re-bedding deck hardware

    I'm in the process of re-beading some deck hardware. Some screw hole had soft wet wet wood which I was able to remove with an allen wrench. I'm just about done with some re-core at the anchor locker, so I was please to find that it haven't spread yet and pouring a plug should do the trick. My...
  4. S

    Hand rail rebedding on Ericson 29

    Hello E-sailors!:egrin: I am in need of some advice. I need to remove my external hand rails from my cabin top, refinish and rebed. However, there is a problem. My E-29 has a hard inner liner with no access hatches to the handrails from the inside and... there is no apparent access to the...
  5. Joe

    Rebedding Leaking Grabrails

    I decided to find the leak coming from the topside grabrails on my E25cb today. After I wrestled the postside grabrail off, I was dismayed at the amount of wet oatmeal I found (first picture). I dug around with a small allen key about as far as the marked dotted red circle shows (second...
  6. S

    Rebedding winches and stanchions

    I'm rebedding the coach top winches and the stanchion bases. I have a couple of questions and would like some thoughts. I'm planning on doing the whole overdrill/epoxy/redrill/backingplate thing. 1. The coach top winches (Barlow 16s) had a thin rubber gasket between the winch base and the...
  7. B

    Best caulk for rebedding

    I'm getting ready to rebed virtually everything on Pie-Rats. Deck has been recored in many places, all holes filled with epoxy, and new Awl-Grip. I'm ready to put all the hardware back on and want to make sure I do it right, and don't have to do it again for a long while. In reading through...
  8. D

    Rebedding Deck Hardware

    I have read several posts regarding bedding deck hardware. Some have suggested just snugging up fasteners and allowing bedding compound to setup before final tightening. Can someone explain the reasoning?
  9. R

    Poll! Keel re-bedding product recommendations!

    Hello All! If you don't know by now I have removed the keel on my E38 and done a bit of restoration on the keel bolts. Now its pretty much ready to go back in and the boatyard and I have done plenty of research on what to use to re-bed the keel and have come up with plenty of options and...
  10. J

    Teak grab rail rebedding

    I need to remove and rebed the teak grab rails on a 1983 35, MK III. Has anyone done this and if so do you have any suggestions? Thanks, John Wressell
  11. J

    Rebedding handrails on an E27

    About to tackle this job and looking for words of advice. It appears i only have access to the end bolts on the handrails due to the inner headliner. Are the others just screws as I can see the outside ones (fore and aft) are bolts with nuts on the inside, please advise. Thanks jarod
  12. R

    Re-bedding Anchor Chain Locker

    This weekend, I’m going to re-bed the anchor chain locker in my E26. I assume that the locker has a flange which is screwed into the recess in the deck. I’m pretty sure I have access to the back “wall” of the anchor chain locker through an access port that’s been installed in the teak bulkhead...
  13. Al Emondi

    Rebedding to hold new motor mounts

    I was wondering if anyone has had to rebed the stringer where the motor mounts attach to? My mounts are old and worn, I have removed the engine from the boat for some fix’in and in the process I noticed that the mounts were held in place with lag bolts. Also, on the starboard side, some...
  14. B

    Single-handed stantion rebedding?

    I'm short on crew to help, so I'm seeking advice on ways to single-handedly rebed the stantions on my E27. The obvious problem is finding a way to hold the nut (inside the hull) while turning the bolt (on deck). Advice? Bob
  15. J

    Rebedding compounds-advice?

    Before I hit WestMarine, I want advice on what bedding compound I should buy to reset my stanchions? John
  16. D

    Stanchion and rebedding.

    Hi All Plan on starting to repack deck hardware this fall on my E33. Read Lorens thread about the stanchion rebuild and have some questons. Did you dig out the core under the base and fill that with epoxy or did you just add a layer a layer of fg on the underside of deck? I was planning on...
  17. A

    Re-Bedding Deck Hardware

    I own a 1978 Ericson 29 and would like some advice on re-bedding the handrails and hatches on the cabin top. The boat has a plastic head liner inside the cabin and there is access only to the first and last bolts for the handrails. What do you recommend I do to remove the handrails so I can...
  18. A

    Re-bedding Hatch Cover Hinges

    I want to re-bed the hatch cover hinges on my 1978 Ericson 29, but cannot access the retaining bolt ends due to the interior liner. Does anyone know how these bolts are connected below the deck? Are they likely to drop down into the void with the liner if I un-bolt them or are they fixed in...
  19. T

    Re-bedding lifeline stanchions, E30+

    I have been of a mind for some time now to re-bed my lifeline stanchions. In planning the job, I see that several of them have nuts that are inaccessible on the interior of the boat due to cabinetry, such as the galley cabinets. Any tips from any of you as to how to deal with this problem...
  20. T

    Rebedding Rub Rail 89' E 38-200

    I think I have sourced my leak to be a section of rubrail and not the genoa track as I had feared. My question is how hard is it to remove and rebed a section? It looks to me like it is all one big piece and that I would need to carefully pry out the rubber/vinyl partion to reveal screws...
  21. T

    E 38-200 Genoa Track Rebedding

    Anyone ever attempted this one? Mine may be leaking some on the strb side. I am not 100% certain if it is the toerail mounted track, the rub rail, or possibly the scuppers. Water is certainly getting in though and when I stick my hand up there it seems to be coming from the toerail area. Looks...
  22. C

    Re-bedding the steering pedastal

    Re-bedding the steering pedestal Has anyone had any experience re-bedding the steering pedestal (Yacht Specialities model I think, definately not Edson) on their E35-3? Mine (1984 hull number 193) shows some evidence of water leaking through the cutout. I was in the locker this weekend...
Top