• Untitled Document

    Join us on March 29rd, 7pm EST

    for the CBEC Virtual Meeting

    All EYO members and followers are welcome to join the fun and get to know the guest speaker!

    See the link below for login credentials and join us!

    March Meeting Info

    (dismiss this notice by hitting 'X', upper right)

e35ii

  1. Zbingham

    E35-II Repowered with Sail Drive ??

    Have you seen or heard of anyone converting to saildrive on an E35ii (or similar)? I don't think it would make sense on the mid-engine/under dinette models since the keel would be in the way. However, I have an aft-engine/under companionway model... It seems that most people that have sail...
  2. Zbingham

    Any info on E35ii hull #541?

    I own E35ii hull#541, currently "Rocinante" .....wondering if anyone out there has any info about her past? Got her out of Vermont. Previous owners had her for some years on stands in their front yard. Not sure where she was last in the water. (The trip to get her was quite an adventure...
  3. R

    need E35-II prop shaft length

    Hi all, My E35-II has the companionway mounted A4 engine (3/4" shaft). I took the shaft/coupling to a local prop shop for a once over and have been told it needs replacing. Being a boat the shaft replacement price came in higher than I expected but the kicker is that they are wanting to...
  4. Lucky Dog

    e35II cradle supports position

    I was breaking ice scrapers this weekend on the frozen snow that cover our boat before I was able to assemble the winter cover. As I was getting warm again sitting in my truck, I noticed the hull deflected from the support on the forward port side. Is there a specific location for the a pads...
  5. R

    The E35-II is a reaching monster

    While this has been stated over and over, there is nothing sweeter than racing experience hammering this point home. As some of you know, I've been frustrated with Sirius' (my refitted 1979 E35-II) performance racing around the buoys for the last several year which has forced (:egrin:) me to...
  6. L

    The Move

    After several years of neglect I finally did it - I moved our Ericson to where I can keep an eye on her - right beside our home. We're moving to Temecula, and we had been keeping our 35-II on a mooring in Newport Beach where it had become an increasingly notorious eyesore after our son was...
  7. R

    To sell or keep Racing my E35-II

    All: I have been racing my 1979 Ericson 35-II (Sirius) on Lake Michigan for a few years now with mixed results (2nd place in double handed Queens Cup this year, 2nd Waukegan to Montrose, 1st Montrose to Waukegan, but lousy finishes in buoy races 4-5th place out of 5 boats). I am totally...
  8. E

    e35-II Bow Chain Plate

    My e35-II bow chain plate failed this weekend (in light air therefore spar still up - lucky). Does any one know where I can purchase a replacement bow chain plate? Is it interchangeable with e35-III?
  9. CaptDan

    E35II Chainplates

    This has probably been discussed before, but I'll ask it anyway: Any E35II owners ever removed their chainplates, and if so how much surgery was involved? Several years ago, I gained access to the port chainplate to repair the rotted bulkhead. That involved a complete dismantling of the...
  10. C

    E35II Anchor and Roller

    Well.... the Dockfather and I were sittin round on a cold day havin an Ale and took a good look at the Weenie 20LB Danforth Anchor and Pathetic Factory Light Duty Roller on the Boat :cool: Figured its time for a Real OffShore Anchor and Roller. Like the 35LB CQR or Delta Plow with Custom Roller...
  11. steven

    E35-II sail area

    The brochure says 533 sq. ft. Anyone know how they came up with that?
  12. CaptDan

    E35II quadrant access

    I'm in process of scoping out an S1 Wheelpilot install later this season, and plan to include the dreaded 'rudder sensor' feature when I begin the project. I hate to admit this, but I don't see an easy way to gain suitable access to the quadrant. How does anyone larger than the average six...
  13. C

    E35II Companionway Hatch Rebuild

    Well....now that the V-Berth and Cabin Hatch are finished :) It's time to start the Companionway Hatch rebuild. Has anyone completed this project :confused: Sure would like some pics. Happy Hatches :egrin: :egrin:
  14. CaptDan

    E35II Bimini

    I'm thinking of adding a bimini this season - to shade our noggins from all that intense Pacific Northwest Sunshine:rolleyes: Have any E35-2 owners with stock mainsheet/traveler/boom arrangement successfully installed a bimini? If so, how large a bimini did you manage? Any installation...
  15. C

    E35II Fuel Tank Replacement Drawings

    Here it is....the Design Drawings for an E35II Fuel Tank Replacement :nerd: The footprint is the same as the Original and increases the height by 6". This provides an increased 15ga of capacity to a 37ga total. The construction is 3/16" welded aluminum. The fill is moved from the Cockpit...
  16. C

    E35II Holding Tank Installation

    Here is the installation of a new 14ga Holding Tank for the E35II. The Tank is a Ronco (www.ronco-plastics.net) Model 245 with Access Port. The dimensions are 24.5"L X 16.5"W X 9.125"H and is the largest tank I could fit in the Salon Setee Locker incuding the 1.5" Hoses. The Access Port...
  17. P

    E35, E35ii & E35iii

    Can anyone explain in simple terms the difference between these three 35's. I'm most likely going to become the new owner of a E35 by the 1st of October. I'm sure I'll probably be asking a lot more questions then.
  18. H

    exhaust system E-35-II

    Hi all Has anyone got a picture they can post of the hot section of and E-35-II...the one with the engine located under the setee in the centre of the salon? The elbow on my set up comes up so close to the botom of the seat that the heat is burning the wood. I have to run with the cover...
  19. S

    Stringer Question E35-II 1979

    Here is the stupid question of the day... I know I do not have the "GRID" on my model...but, Does my vessel have "stringers" and where are they located? I have searched all around the hull and find nothing that I would consider a "stringer." I want to find these elusive "stringers," (if...
  20. R

    Which spade rudder for E-35II

    I am presently restoring/refitting a 78 35MKII. I have two (2) rudders available for install. One is the 70's trapezoid-shaped type from a 70 35MKII. The other is the newer hawkbill- shaped type with slightly less surface area. It came un-installed with my boat. I would appreciate...
  21. M

    Engine Exhaust System e35II

    Enjoyed reading about Nicki's purchase and planned sail of his E-35II..... Nicki, and to all other's owning an E35II.....take a look at your boat's exhaust system. I've just purchased and installed a new Yanmar engine due to sea water entering my engine block through the exhaust system...
  22. M

    need a staysail E-35II

    Looking to buy a used or new staysail for my E35II. Anyone aware of any sails that will work for this purpose, or a loft where I might pick one up... thanks... Alan Masallah
  23. C

    E35-II RePower Update

    Here are some pics on the Engine Stringer progress on the Beta 902 Repower. This is (4) layers of Epoxy / 23oz double bias fabric. (4) more layers to go for 3/8" to 1/2" structural thickness :p The engine mounts will be fastened to 3/8" x 3"x 22" SS Bar Stock. The Bar Stock will be...
  24. C

    E35-II Repower Blues

    Well... here is the update on the Repower Blues. Had a local diesel rebuilder tear the ole 90' Universal M4-30 down for an estimate and what do you think we found ? The PO overcranked it with the raw water valve open a few to many times and sea water had entered the crankcase. The guts are...
  25. C

    E35-II AC/DC Panel-Wiring Upgrade

    Well....it's that time again ! Gotta rewire and install new AC/DC panels for the ole 74' E35-II. I have seen various panel arrangements and I am looking at moving the whole gang to the NAV Station locker area :confused: My connected load requires (4) AC Breakers + 30A Main and 20 +/- DC...
  26. C

    E35-II Wood Engine Bed ?

    Are wood stringers the best alternative to replaceing the rusted steel engine bed in the E35-II ? :confused: The current bed is an angle iron sled glassed in to the hull with some sort of sound insulation underneath. The legs are going...GONE! :eek: The BEST engine bed rebuild found so...
  27. C

    E35-II Engine Mount

    Thank you all for helping me with a successful and safe engine removal. I used the Fly Girl Method (good one Leighton :D ) Ran the main halyard to the topping lift. Now you have a crane arm. Used an 8' 4x4 strapped to the boom for the first move off the mounts Slid the engine on a piece of...
  28. C

    E35-II Engine Removal

    Well...looks like the ole Universal 4-30 needs an overhaul :boohoo: The engine is located in the salon. I need some advise on the removal. Saw a post a while back with pictures on a wisker pole hoist stringer arrangement...can't seem to find it. As anyone has done this replacement, would...
  29. C

    E35II Fuel Tank Replacement

    Here is progress on fuel tank replacement for the 74' 35II. Went with 3/16 welded alluminum and electronic (Centroid) fuel sender. The new tank fit easily in to the original footprint with an additional 18 GA. I just increased the height by 10" and went from 22GA to 40GA. Hope this helps...
  30. T

    1977 E35II for sale - Sausalito, CA

    I recently purchased a new boat and my 1977 Ericson 35 is foor sale. In the last three years I've done the following: New full batten main and jib (neill pryde) New Universal Diesel - (15 hours) New AC and DC wiring with new distribution panels and GFCI outlets 660 amp hours of battery...
Top