• Untitled Document

    Join us on March 29rd, 7pm EST

    for the CBEC Virtual Meeting

    All EYO members and followers are welcome to join the fun and get to know the guest speaker!

    See the link below for login credentials and join us!

    March Meeting Info

    (dismiss this notice by hitting 'X', upper right)

exhaust

  1. Exhaust System Upgrade

    E38 Exhaust System Upgrade

    I’d been experiencing a little of the white steaming from the exhaust system the last two seasons, no overheating issues as the boat still holds 185f at cruising speed. So I’d been systematically going through the heat exchanger system and checking for blockages etc. Now I was finally onto the...
  2. New Elbow.jpg

    New Elbow.jpg

    New Elbow with Heat shield from HDI Marine
  3. 20200517_152715.jpg

    20200517_152715.jpg

  4. Helper.jpg

    Helper.jpg

    My daughter helping with the new thru hull install
  5. Nick J

    Misadventures of a new diesel owner

    Hey, did you know these boats actually sail too? You wouldn’t know it watching me over my first 4 months of ownership, but we were finally able to take Segue (soon to be renamed) out for the day. I had a small scare when I went below to find the new exhaust riser smoking a bit when I was...
  6. exoduse35

    Heater exhaust

    I am about to install my new heater ( a force 10 propane) to the bulkhead between the main cabin and the head of my 35-2. As I look at it I can see the simple and least destructive way to route the exhaust would be to run it out through the hatch instead of punching a hole in the roof. The...
  7. B

    Exhaust Elbow Needed!

    I'm looking for a replacement exhaust elbow, part #170-2834 that I believe was made by Onan, for my 1988 E32-200 with the Universal M25XP engine. See the attached pictures. Any idea on sources for this part? Also, when I took the system apart I found the water injection port to be nearly...
  8. P

    Exhaust check valve

    AS OF TODAY, BETH & I ARE THE PROUD NEW OWNERS OF "INVICTUS" A 1981 E-28+.:egrin: WE SPENT THE DAY ON BOARD CLEANING & MAKING MINOR REPAIRS AFTER SHE SPENT THE LAST 1 1/2 YEARS ON THE HARD. THERE IS A CHECK VALVE IN THE EXHAUST BETWEEN THE DIESEL ENGINE AND THE MUFFLER. THE SURVEYOR SAID THIS IS...
  9. mherrcat

    Exhaust manifold studs

    I will be removing my exhaust manifold to install studs that are long enough for the new alternator mounting bracket. Any insight on what to expect when I try to remove those studs? How have others done it and are there any pitfalls to avoid? What about the exhaust manifold gaskets? Do they...
  10. A

    YSB-8 siphon break and exhaust

    I need some help. My YSB-8 runs well except for a small amout of exhaust steam but I am confused as to why I seem to get much more water flow out of the siphon break into the scupper than acutal output of cooling water through the waterlock and out the exhaust. I have checked all the hoses and...
  11. bayhoss

    Exhaust riser inlet

    At the time of purchase my E28 (Universal M12) had the raw water line that leads to the exhaust riser in the vertical position (green hose). Can anyone think of any harm that would be done by rotating the hose fitting 90* so that the water drained away from the riser? Thanks in advance, Frank
  12. R

    Exhaust design question...

    Hello All, I'm in the process of R-n-R'ing the 5432 in my E38 with a used engine. In the process of removing the engine several other things are receiving attention including the exhaust system. Currently the exhaust leaves the engine from a 2" OD water mix elbow, travels about 10" of hose...
  13. V

    exhaust for a westerbeke 4-107

    I'm reinstalling an exhaust system for my westerbeke diesel in my E-41. There is a v-drive, so the engine is mounted forwards back. Any diagrams or drawings for this particular project? I looked through some basic diesel mechanic books but I'm wondering if anyone had some specific information.
  14. A

    E-27 exhaust tubing

    before and after of the exhaust tubing for my E-27. The before (rusted one) has an obvious flaw that the water from the engine goes into the engine during start up because there is no loop in the tubing. I attempted to fix this by constructing a new exhaust. I need your opinion to make sure my...
  15. P

    E27 exhaust loop

    My 1976 E27 has an Atomic 4 with an upward loop (galvanized) in the exhaust line at the thruhull in the stern. Any Ericson owners out there have the same setup? I spoke with Don Moyer and he didn't recall any boats using the A4 with this. The reason for asking is I have some restriction...
  16. S

    Increased engine noise due to exhaust riser closing??

    Sorry if this has been asked, I could not find it. My engine noise is louder than in previous years. This only occurs at idle. With an increase in rpms there is little noise. Could it be that the exhaust riser arm is becoming clogged where the water comes in but with increased rpms more water...
  17. F

    1986 38-200 Diesel Exhaust Hose Pathway

    Hello Everyone, I've been away quite a long time, but I'm back with a quick question. Does anyone have a diagram of the pathway for the large exhaust hose on my Universal Atomic Engine. I know it runs unseen under the sole near the shower sump basin, then disappears behind the cabin ladder...
  18. S

    Exhaust Piping Insulation

    Hi all, 1976 E 32 (Atomic 4) Last year I bought some fiberglass tape for exhaust lines from West Marine. My engine exhaust pipe from my engine to the first elbow was exposed It is the stuff that comes with a thin aluminum cover. I wrapped the pipe with the aluminum foil on the outside. My...
  19. J

    Exhaust sooty when submerged?

    Hi all, New to the forum (and sailboats in general for that matter) so this may be a silly question, but any thoughts are greatly appreciated - I have an ericson 30+ and was out motoring around the other day and noticed that when I go above around 60% power (which we try not to do often) the...
  20. Sven

    Extending exhaust to reduce diesel soot ?

    We just had our E39-B polished and waxed ... very nice :-) Of course, as soon as we started up the diesel after the "service" we got a black streak running down the hull at the stern. My gut reaction is to try to attach a 1" (or so) extension to the exhaust to keep the sooty drip from...
  21. F

    does exhaust manifold gasket need sealant?

    I'll be ordering a new exhaust bracket gasket for my Universal 25x engine. Do you have to put some kind of permatex gasket sealear on a new gasket on a hot exhaust system?
  22. F

    fixing loose exhaust pipe

    Hi folks, I have another thread on installing a new alternator bracket. While doing this job I discovered that the 1 1/4" pipe coming out of the exhaust manifold bracket is loose. You can even shake it side to side. I'm current struggling with removing the exhause hose, I'll probably have to...
  23. mherrcat

    M-18 Exhaust Riser

    On the top of my exhaust riser there is a small plug similar to the plug that holds the zinc in the heat exchanger. There is also a larger plug on the port side of the riser at the bottom near the exhaust flange. What are the purpose of these plugs?
  24. bigd14

    e27 with A-4 Exhaust- Replacement Help Needed

    Hey everyone- I've started to address the exhaust system on my raw-water cooled Atomic 4 in my 1972 E-27. It looks like its been poorly cobbled together, with a very loose attachment to the manifold (at least it came off easily!) and no support or anchors anywhere. The exhaust exits the...
  25. Bolo

    Exhaust elbow riser fitting problem

    I have an E-32 III with a Universal M-25XP engine. The original exhaust elbow riser started showing rust spots on either side of the elbow indicating that it was failing. The metal was rusting out at both spots so I figured it was time to replace the unit. I contacted Torrensen Marine, via...
  26. simdim

    Slight exhaust smell

    Folks, Now since we had re-raked the mast our e29 sails sweet :egrin:( thanks to everyone on this forum for the help), but Admiral had noticed that there is exhaust smell in the cabin and port lazareth. PO had retrofitted Yanmar 2gm20 and from what I can see all ventilation hoses are a mess -...
  27. M

    No or very little water in the exhaust?

    Hi all Last Sunday we went for a day sail and on the return when we fired up the diesel there was no water coming out with the exhaust, maybe a couple of drops. The anti siphon vent was putting out a good stream of water so I know that there was cooling water going into the heat exchanger...
  28. D

    Torque Settings For Exhaust Manifold

    Does any one have torque setting for exhaust manifold studs and nuts for 1982 M25. I believe studs and nuts are about 3/8 fine thread, not certain on size, they out on boat.
  29. Cory B

    Exhaust anti-siphon hose

    Hello, Ours (and most 80s-vintage Ericsons?) have a funky antisiphon hose coming off the exhaust thruhull. It is above the standing water line, but sometimes below the sailing one. Ours is made of a small rubber hose that does not appear to be rated for exhaust or anything, but most...
  30. R

    Universal 5432/M40 exhaust elbow?

    Looking at the exhaust on my 5432 last weekend it occurred to me that it could be improved. The exhaust exits the riser to a hose that is tapered and clamps to a 90* bronze plumbing fitting then to the waterlift muffler. The 90* fitting is a standard marine plumbing fitting with screw in hose...
  31. D

    Exhaust Mainfold

    Does anyone have any experience removing the exhaust manifold off an 80`s vintage M25? I broke one of the mounting studs and believe it has to come off to replace broken stud.
  32. D

    E 38-200 Exhaust Elbow Temp and Aft Cabin

    Hi: I have a 1988 E 38-200. The engine runs at a steady 160 degrees (though I do have some steam). I noticed after a 1.5 hour run yesterday at 2100 rpm that the area in the aft cabin that nearly abuts the exhaust elbow was hot to touch. Is this normal? Is is possible to have a normal...
  33. H

    exhaust system E-35-II

    Hi all Has anyone got a picture they can post of the hot section of and E-35-II...the one with the engine located under the setee in the centre of the salon? The elbow on my set up comes up so close to the botom of the seat that the heat is burning the wood. I have to run with the cover...
  34. M

    Exhaust Pipe Wrap

    What is a good kind of exhaust pipe wrap?
  35. treilley

    Exhaust manifold leak

    We ran our first race of the season tonight. I have not run the results yet but it appears as though we placed second out of about 10 boats behind a Sabre 38, When I first started the motor, Kathy smelled something burning. It was actually antifreeze. I checked the engine and there was a...
  36. jreddington

    Exhaust System Elbows and Check Valves

    Posted the below on the Sailnet Ericson group. Got some good feedback, but the more the merrier. I'm still looking for sources for the bronze elbows, especially since one has to go in about a foot beyond the mixing elbow and the fiberglass elbows say you need to be at least two feet away...
  37. R

    E27 exhaust setup

    Does anyone have any photos or drawings of factory exhaust setups for the E27? I don't like the one in my boat and would like to see other owner's setups.
  38. Mike Thomas

    Waterlift exhaust system question

    I am replacing my old water jacket type of muffler with a Water lift muffler in my 76 E-29. I have piped the exhaust in the same configuration as the water jacket and will locate the Water Lift muffler in the port cockpit locker. The muffler will sit at about the waterline. I have piped the...
  39. M

    Engine Exhaust System e35II

    Enjoyed reading about Nicki's purchase and planned sail of his E-35II..... Nicki, and to all other's owning an E35II.....take a look at your boat's exhaust system. I've just purchased and installed a new Yanmar engine due to sea water entering my engine block through the exhaust system...
  40. R

    E27 Exhaust Riser

    Just found a exhaust leak in the exhaust riser on my atomic 4. I'm replacing the black iron pipe riser and trying to order parts. I forgot to measure the nipple length. Anyone who has cobbled up a pipe riser remember how long the straight pipe nipple is? 4 6 or 8 inches????:rolleyes: ( I'm...
  41. D

    Rust In Exhaust Water

    When I first start my water-cooled Universal 11 HP diesel, the first gush of water that comes out has rust in it - a cloud of rust stains the water. Then the water runs clear and there is no problem after that. The engine runs perfectly, I have just replaced the heat exchangher zinc (it was soft...
  42. N

    What is normal exhaust?

    My E28's Universal MK12 has water flowing out of the anti-syphon port as well as the exhaust at all attitudes, speeds, and sea conditions, i.e., whenever the engine is running. My boat yard foreman asked me if that was normal. I realized that I did not know. Is it normal, or is it an...
  43. E

    exhaust what is it

    just purchased a 74 35 II... it has an a4. at the exhaust it goes into some kind of galvinized pipe. there is also a hose that goes from the exhaust manifold into this pipe. there is heat insulation from the engine to this pipe. on the other end it does a 90 degree turn up and then does another...
  44. E

    exhaust what is it

    just purchased a 74 35 II... it has an a4. at the exhaust it goes into some kind of galvinized pipe. there is also a hose that goes from the exhaust manifold into this pipe. there is heat insulation from the engine to this pipe. on the other end it does a 90 degree turn up and then does another...
  45. M

    29' exhaust riser

    I have a 1970 E29T that originally had an atomic 4. Has anyone had to replace/rebuild the copper (bronze?) water jacketed exhaust riser? If so, what did you use?
  46. S

    Vented Loop in Exhaust Hose

    I have an E27 with a Palmer P60. This is a raw water cooled engine with a water lift muffler. The exhaust hose currently rises from the muffler to the top of the lazarette then loops back down to the thru-hull outlet. Should I place a vented-loop in the exhaust line? Thanks in advance. Steve...
  47. S

    Exhaust on E-27

    I have a 1977 E-27 with an Atomic 4 that I have had for 1 year. Please bear with me this is a convoluted explanation but there is a question in here somewhere. This was my exhaust layout - leading aft from the engine, screwed into the exhaust flange is what appears to be a 16" piece of pipe...
  48. D

    e29 Exhaust

    I am replacing my standpipe with a Vetus waterlock. The only place I can install it is thr lowest froward corner of the lazarette, but the problem is that there is ZERO drop from the manifold exhaust out let to the Vetus inlet. Has anyone tried this? Any suggestions?
  49. R

    Exhaust Hose for E32-3

    Hi, all, does anybody have by any chance a list of hoses used in E32 with diameters and lengthes? Some hoses are rather hard to measure accurately... Thanks in Advance, Stanly
  50. D

    exhaust steaming & cooling system

    we own a 1988 38-200 with the Universal 5432 engine. Above 1800 rpm with a temp of 150f we start seeing some steam which increases with increasing rpm. At 2200 temp will be 175-180. temps seem normal but we are concerned about the steaming. any ideas? in looking at the system we see a small...
Top