Page 3 of 3 FirstFirst 123
Results 31 to 34 of 34

Thread: Universal M25 Exhaust Riser/Elbow Options

  1. #31
    Sustaining Member Sati's Avatar
    Join Date
    Jul 2018
    Location
    Seattle, WA
    Posts
    97
    Quote Originally Posted by Kenneth K View Post
    Jeff, there's only three nuts holding the flange to the manifold. Put a wrench on them. If you can turn them all, it might be easy. I didn't have the clearance to get a box end wrench on the bottom nut and was afraid of rounding it off with an open-end wrench. I used a drill and wire wheel to polish the surfaces before re-gasketing.

    If you do it in place though, it's a bit of a wasted effort in my opinion. You might as well take the riser/elbow off the boat and get it cleaned out. Performance Radiator in Tacoma will do it. Otherwise, you're leaving that as a potential problem for later.

    Heck, if you can turn the bolts in place, you might try snugging them up to see if you can minimize the leakage. Then you can use your boat this weekend and do the full job when you have the time.
    Thanks, Ken. Good call on doing the whole job / doing it right if I'm going to do it. I tried wrenching the nuts this morning and lo and behold, I was able to snug them up about a quarter turn each. Wiped off the coolant spills on the engine, went motoring, and had a dry engine upon return. Sometimes it's an easy fix.

    I'm going to keep a cooling system maintenance run as a close-term checklist item, though -- clean the riser, replace the gasket, clean/flush the heat exchanger, hoses, the whole shebang.

    I do notice the water heater seems to be leaking drops / drips of coolant but I wager that's likely a hose clamp issue.

    *edit*: hot water heater, not water cooler
    *edit2*: water heater, not hot water heater (buncha wise guys here)
    Last edited by Sati; 11-08-2018 at 04:36 PM.
    Geoff W.
    s/v "Delightful"
    1987 E32-3
    Hull #712

  2. #32
    Sustaining Partner Kenneth K's Avatar
    Join Date
    Mar 2016
    Location
    Gig Harbor, Wa
    Posts
    295
    Blog Entries
    6
    A bit of luck.....glad to hear it.

    Don't forget to also check the elbow where the raw water is injected back into the riser. Mine was 80% blocked and causing steam with too little water flow at exhaust thru-hull. If clogged, you can chip the particulate out with a small screwdriver and reuse the fitting.
    Ken
    '85 E32-3 "Mariah" #641
    Universal M-25

    "Saltwater is the cure; sweat, tears, or the sea......"

  3. #33
    Moderator Christian Williams's Avatar
    Join Date
    Oct 2012
    Location
    Los Angeles
    Posts
    3,477
    Blog Entries
    77
    *edit*: hot water heater, not water cooler

    More edit: water heater.

    As I was asked in a post not long ago, "why do you need to heat your hot water?"

    Thelonious II, E381 hull 513 (1984) Universal 5432
    Table of Contents for Thelonious Blog here
    Videos: http://www.youtube.com/c/ChristianWilliamsYachting

  4. #34
    Sustaining Partner Bolo's Avatar
    Join Date
    May 2006
    Location
    Annapolis, MD
    Posts
    290
    Quote Originally Posted by Christian Williams View Post
    *edit*: hot water heater, not water cooler

    More edit: water heater.

    As I was asked in a post not long ago, "why do you need to heat your hot water?"

    Because if you have a “first mate” (wife) aboard who likes to have hot water when you anchor too far from a 120 volt outlet you need to heat your hot water. That’s why. Boiling some on the galley stove just doesn’t cut it.
    Bob Skalkowski
    1987 E32 III (#722) - "Vesper"

Similar Threads

  1. replacement exhaust riser on 5411 universal
    By Allen Jenneman in forum Maintenance & Mechanical
    Replies: 4
    Last Post: 07-31-2016, 04:37 AM
  2. E 32-3 Exhaust elbow/riser
    By Eric B in forum Maintenance & Mechanical
    Replies: 9
    Last Post: 02-06-2015, 06:07 PM
  3. Universal 5432/M40 exhaust elbow?
    By rwthomas1 in forum Maintenance & Mechanical
    Replies: 14
    Last Post: 06-17-2012, 08:28 PM
  4. Exhaust elbow riser fitting problem
    By Bolo in forum Maintenance & Mechanical
    Replies: 7
    Last Post: 11-17-2008, 07:46 AM
  5. E27 Exhaust Riser
    By RicoPaolino in forum Maintenance & Mechanical
    Replies: 2
    Last Post: 05-30-2006, 06:22 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •